Key Features:
Through The
Wall or Chimney Vented
Compact, Low
Profile Design
83% Efficiency
Rating
Water-Tight
Metal Push Nipples
Long Life Cast
Iron Heat Exchanger
Corrosion Resistant
Stainless Steel Burners
50,000 - 200,000
BTU/H Input
Venting and Installation
Flexibility
The ODV-B Series boiler
can be vented vertically up a chimney or horizontally
through an exterior wall making it a convenient and cost
effective choice for a variety of applications. Standing
less than 31 inches high, this low profile boiler fits
into areas that other boilers can not. The ODV-B is also
an ideal choice when converting a home from electric heat
to a hot water system.
Cast Iron Heat Exchanger
The ODV-B utilizes cast
iron construction because of its durability and efficient
heat transfer capabilities. Cast iron sections and push
nipples are an integral part of each ODV-B heat exchanger.
Using only the highest quality cast iron and heat transfer
designs, the ODV-B will provide many years of efficient
and trouble-free operation.
High Energy Efficiency and
Lower Heating Costs
With
efficiency ratings as high as 83%, the ODV-B provides
increased energy savings resulting in lower fuel bills.
With the potential cost savings this represents, the
ODV-B boiler will pay for itself in a few short years.
Key Features:
Cast-iron sections
and push nipples
Automatic Stack
Damper
Corrosion resistant
stainless steel burners
Energy Efficiency
Ratings up to 84.1%
Standard Pilot
or Electronic Ignition
Integral draft
hood, natural draft chimney vented
| Quality
Cast Iron Heat Exchanger
 The OMGB utilizes cast iron construction because of its durability
and efficient heat transfer capabilities. Cast iron
sections and push nipples are an integral part of
each OMGB heat exchanger. Dual thermal flow speeds
heat transfer. Hot flueway gases pass around hundreds
of staggered studs on the flueway wall, providing
rapid heat transfer to the boiler water. Internal
baffles agitate the circulating water, so it heats
quickly and uniformly. Using only the highest quality
cast iron and heat transfer designs ensure that
the OMGB will provide many years of efficient and
trouble-free operation.
Fuel Saving Components
 Advanced engineering can be found in every part of a OMGB boiler.
An optional "on-demand" ignition control
eliminates wasted fuel associated with a continuously
burning pilot light. In addition, an integrated
automatic vent damper closes when the burner shuts
off, preventing heat from leaving through the chimney
saving fuel and heating costs.
Easy Installation and
Maintenance
A compact design
and special packaging features make the OMGB boiler
easy to install and service. An integrated flue
collector and draft hood allows for easier installation
in cramped areas. The pilot assembly is easily accessible,
located on the orifice side of the burners, out
of the main combustion area. The OMGB comes factory-assembled,
wired and tested to eliminate costly field assembly
and reduce installation time.
Stainless Steel Burners
Corrosion resistant
atmospheric stainless steel burners are incorporated
into each OMGB boiler delivering uniform flame patterns
that optimize combustion efficiency and quiet operation.
Manufacturers Limited
Lifetime Warranty
Olsen HVAC backs
its residential, cast-iron heat exchangers with
a Limited Lifetime Warranty. This Warranty is meant
to protect your investment, but is also offered
to illustrate our commitment to customer satisfaction. |
| |
Key Features:
87% AFUE Efficiency
Sealed Combustion
Technology
Venting Flexibility
- Side Wall or Vertical
Quiet Operation
3 Sizes-Capacities
From 50,000 to 140,000 BTU/h
Reliable Honeywell
Ignition Components
Sealed Combustion Technology
for Safer, Cleaner Heat
The OSC Series boiler
draws in outdoor air to mix with fuel in the combustion
process. This guarantees consistent air supply and optimizes
clean burning. Sealed combustion design not only protects
against harmful CO due to poor combustion, but also conserves
heated air within the living space.
Installation Flexibility
The OSC boiler has a
low profile design and can be installed virtually anywhere.
The boiler can be placed adjacent to any exterior wall
and vented directly outdoors or vented vertically utilizing
stainless steel vent pipe. This makes it easy to incorporate
the OSC into new home construction or as a replacement
to an existing boiler. The OSC is an ideal choice when
converting from electric heat to a hot water system.
Cast Iron Heat Exchanger
The OSC utilizes cast-iron
construction because of its durability and efficient heat
transfer capabilities. Cast-iron sections and push nipples
are an integral part of each OSC boiler. Using only the
highest quality cast iron and heat transfer designs, the
OSC will provide many years of efficient and trouble-free
operation.
Stainless Steel Burners
Corrosion resistant
stainless steel burners are incorporated into each OSC
boiler delivering uniform flame patterns that optimize
combustion efficiency and quiet operation.
High Energy Efficiency and
Lower Home Heating Costs
With an 87% efficiency rating, the OSC boiler offers the highest
cast iron to Btu heating capacity ratio in the industry.
Once the OSC boiler is installed, the payback will begin
immediately due to reduced energy consumption and lower
heating costs. Homeowners may even be eligible for utility
rebates, depending on geographic location and energy provider.
Factory Tested, Pre-Wired
& Packaged
The OSC boiler arrives
ready to install. Prior to leaving the factory, nine quality
assurance checks ensure trouble-free start-up and performance.
Manufacturer’s Lifetime
Warranty
The most straightforward
warranty in the industry — lifetime warranty to
the original homeowner covering the entire heat exchanger
— not just the sections.
Features & Benefits:
Easy Maintenance
Cast Aluminum
Heat Exchanger
Air/Fuel Mixer
Pressure Switches
Integrated
Boiler Control
Secondary Heat
Recovery Unit
PVC Vent Pipe
Induced Draft
Fan
Remarkable
90% AFUE Efficiency
The Q90 dramatically reduces fuel consumption and pays
for itself with substantial annual fuel savings. Its efficiency
is increased beyond 90% when used in low temperature systems,
such as radiant systems.
Revolutionary
Cast Aluminum Heat Exchanger
Transfers heat three times faster with greater thermal
conductivity than conventional cast iron. It produces
enormous gains in heat-up speed and operating efficiency.
Also, the packaged boiler weighs only 220 pounds for easier
installation.
Safe,
Economical CPVC and PVC Vent Pipe
Cooled flue gas can be safely vented through inexpensive
readily available and easy to install PVC, after 5' of
CPVC provided with the unit. The air intake also utilizes
PVC pipe.
Sealed
Combustion, Direct-Vent System
Unlike conventional residential atmospheric and induced
draft boilers, the Q90 draws fresh air from outdoors for
combustion, instead of air from inside the home. Therefore
it does not compete with building occupants for its air
supply. With this design the Q90 runs quieter than a traditional
boiler.
Simplified
Controls
The Quantum 90’s simple design is engineered to
maximize reliability. The Q90 incorporates an integrated
boiler control for operation, safety and diagnostics.
A High Temperature Limit Control is included for additional
safety. Ignition is provided by a hot surface igniter
and a single stage gas valve. A single pressure switch
ensures air intake and exhaust vents are clear. All components
are easily accessible through the removable door.
Environmentally
Friendly
The Q90's direct-vent system, premix gas burner and low
flame temperature substantially reduce CO and NOx emissions
(acid rain and smog components).
Features & Benefits:
Low Water Cut-off
Easy Maintenance
Combustible
Floor Plate
Cast Aluminum
Mono Block
Air/Fuel Ratios
Piping Options
Integrated
Boiler Control
Supply-Side
Pumping
PVC Vent Pipe
Forced Draft
Fan
| Remarkable 90% AFUE Efficiency
The Q90-200 dramatically reduces fuel consumption
and pays for itself with substantial annual fuel
savings. Its efficiency is increased beyond 90%
when used in low temperature systems, such as radiant
systems.
Revolutionary Cast Aluminum “Mono Block” Heat Exchanger
This one-piece heat exchanger design eliminates
leaks that can occur due to section interface with
sectional heat exchangers. The greater thermal conductivity
of cast aluminum transfers heat three times faster
than conventional cast iron, producing enormous
gains in heat-up speed and operating efficiency.
Also, the packaged boiler weighs only 220 pounds
for easier installation.
Simplified Controls
The Quantum 90-200’s control design is engineered
to maximize reliability. The Q90-200 incorporates
an integrated boiler control with high limit and
low water cut-off for operation, safety and diagnostics.
Ignition is provided by a hot surface igniter and
a single stage gas valve. Dual switches ensure air
intake and exhaust vents are clear. All components
are easily accessible through the removable door.
Sealed Combustion, Direct-Vent System
Unlike conventional atmospheric boilers, the Q90-200
draws fresh air from outdoors for combustion, instead
of air from inside the home. Therefore it does not
compete with building occupants for its air supply.
With this design the Q90-200 runs quieter and more
efficiently than a traditional boiler.
Safe, Economical CPVC and PVC Vent Pipe
Cooled flue gas can be safely vented through inexpensive
readily available and easy to install PVC, after
5' of CPVC provided with the unit. The air intake
also utilizes PVC pipe.
Environmentally Friendly
The Q90-200's direct-vent system, premix gas burner
and low flame temperature reduce CO and NOx emissions
(acid rain and smog components) by more than 30%
and 50% respectively. |
| |
